Lefant Nautica Hard Eco Dark Blue 2,5L
Saatavilla vain verkkokaupasta
Toimituskulut alk
3,90€
PRODUCT DATA
Colors: Dark Blue, Black
Coverage: 13m²/liter
Finish: Matte
Compatibility: Direct over Lefant Mark 5, TF, Nautica Copper and most of other hard and semi hard solventbased antifoulings.
Volume Solids: 50 ±2% (ASTM D2369)
Flash Point: 30°C
Specific Gravity: 1,44 (ISO 2811-1)
Shelf Life: 2 years (min)
VOC: 430g/l (ISO 11890-2/2006)
Unit Size: 750ml, 2500ml
APPLICATION DATA
Application: Brush, Roller
Coverage: 13m²/liter
Film Thickness: 40-60µ (dry)
Number of Coats: 2 coats for seasonal protection. Extra coats in areas where the fricton and wear are higher, such as rudder, stem, waterline.
APPLICATION INTERVAL
Temperature - 10°C Min - 20°C Min/Max
Overcoating - 10h - 6h
Launching - 24h - 12h/2 mth.
Conditions during application: Do not paint in wet or humid conditions. The substrate temperature should not understep +5°C during the application and 6 hours after the job is done. Drying times and overcoating intervals will increase with thicker paint layers. When applying in confined spaces, make sure the area is sufficiently ventilated.
SURFACE PREPARATIONS
Surface in good condition: Remove all traces of loose paint and contamination by sanding the entire surface well with 80 grit sandpaper. Remove sanding debris.
Surface in poor condition: Completely remove all old antifouling paint using Lefant Paint Remover or by sanding or sandblasting to near base surface.
Surface of BARE Gelcoat/GRP: It is very important that bare gelcoat/GRP be properly prepared. Remove mold release wax using Lefant Boat Cleaner concentrated followed by using Lefant IPA Surface Cleaner.
Sand the surface rough (grit 80)and fill any surface imperfections with
Lefant Epoxi Filler following the label instructions. Apply at least one layer of Lefant Epoxi Primer by following label instruction.
PRODUCT DATA
Colors: Dark Blue, Black
Coverage: 13m²/liter
Finish: Matte
Compatibility: Direct over Lefant Mark 5, TF, Nautica Copper and most of other hard and semi hard solventbased antifoulings.
Volume Solids: 50 ±2% (ASTM D2369)
Flash Point: 30°C
Specific Gravity: 1,44 (ISO 2811-1)
Shelf Life: 2 years (min)
VOC: 430g/l (ISO 11890-2/2006)
Unit Size: 750ml, 2500ml
APPLICATION DATA
Application: Brush, Roller
Coverage: 13m²/liter
Film Thickness: 40-60µ (dry)
Number of Coats: 2 coats for seasonal protection. Extra coats in areas where the fricton and wear are higher, such as rudder, stem, waterline.
APPLICATION INTERVAL
Temperature - 10°C Min - 20°C Min/Max
Overcoating - 10h - 6h
Launching - 24h - 12h/2 mth.
Conditions during application: Do not paint in wet or humid conditions. The substrate temperature should not understep +5°C during the application and 6 hours after the job is done. Drying times and overcoating intervals will increase with thicker paint layers. When applying in confined spaces, make sure the area is sufficiently ventilated.
SURFACE PREPARATIONS
Surface in good condition: Remove all traces of loose paint and contamination by sanding the entire surface well with 80 grit sandpaper. Remove sanding debris.
Surface in poor condition: Completely remove all old antifouling paint using Lefant Paint Remover or by sanding or sandblasting to near base surface.
Surface of BARE Gelcoat/GRP: It is very important that bare gelcoat/GRP be properly prepared. Remove mold release wax using Lefant Boat Cleaner concentrated followed by using Lefant IPA Surface Cleaner.
Sand the surface rough (grit 80)and fill any surface imperfections with
Lefant Epoxi Filler following the label instructions. Apply at least one layer of Lefant Epoxi Primer by following label instruction.
- EAN: 7393461050541
- Tuotenumero: 103578317
- Toimittajan tuotenumero: 129-91-3503-2
Verkkokaupan maksutavat:
